Which Fret is Buzzing - FRETS.NET2024-03-28T12:45:20Zhttps://fretsnet.ning.com/forum/topics/which-fret-is-buzzing?commentId=2177249%3AComment%3A56155&feed=yes&xn_auth=noI find an analog VOM easier t…tag:fretsnet.ning.com,2011-05-08:2177249:Comment:567892011-05-08T02:22:10.769ZMark A. Kanehttps://fretsnet.ning.com/profile/MarkAKane
<p>I find an analog VOM easier to use with this method. The needle jumps and lags slightly, giving you plenty of time to see the action, so to speak. Its difficult to listen for a beep when you are plucking a note as well. As for attaching the lead to the fret, I have an old lead missing its tip so I have stripped the wire bare and I use a small piece of tape.</p>
<p>Having said all this, I haven't done this in ages! 19 years of staring at frets has honed a sixth sense (which one I don't know)…</p>
<p>I find an analog VOM easier to use with this method. The needle jumps and lags slightly, giving you plenty of time to see the action, so to speak. Its difficult to listen for a beep when you are plucking a note as well. As for attaching the lead to the fret, I have an old lead missing its tip so I have stripped the wire bare and I use a small piece of tape.</p>
<p>Having said all this, I haven't done this in ages! 19 years of staring at frets has honed a sixth sense (which one I don't know) such that diagnosis comes somewhat easier these days, BUT not always!</p> Actually, using a VOM makes a…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:562312011-05-04T22:14:23.591ZNed Knepphttps://fretsnet.ning.com/profile/NedKnepp
<p>Actually, using a VOM makes a lot of sense. It's not expensive to get one which indicates continuity with a beep. You don't need to watch anything but where you are placing the probes. Usually, even the slightest contact will make a beep. Of course it should beep on the fret played but you should have silence anywhere else unless it touches.</p>
<p> </p>
<p>I think the light bulb approach would be much less sensitive that a VOM.</p>
<p> </p>
<p>Radio Shack should have alligator clips that…</p>
<p>Actually, using a VOM makes a lot of sense. It's not expensive to get one which indicates continuity with a beep. You don't need to watch anything but where you are placing the probes. Usually, even the slightest contact will make a beep. Of course it should beep on the fret played but you should have silence anywhere else unless it touches.</p>
<p> </p>
<p>I think the light bulb approach would be much less sensitive that a VOM.</p>
<p> </p>
<p>Radio Shack should have alligator clips that will fit your VOM probe tips or you may be able to find new leads with the clip built in instead of the probe. If push comes to shove, just buy bare alligator clips and fit (crimp) them to the end of which ever probe you want to clip on the string. Just make sure it is clipped it below where you are testing and that it isn't touching any other strings. </p>
<p> </p>
<p>Ned</p> As you indicated, I don't kno…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:561602011-05-04T20:09:40.579ZDoug Collinshttps://fretsnet.ning.com/profile/DougCollins
<p>As you indicated, I don't know how well this would actually work, but I think it's a brilliant idea! I'm sorry that I have fixed the buzz now. I want to try it.</p>
<p> </p>
<p>I think it is a two person job though unless I can figure out how to attach the probe to the fret.</p>
<p> </p>
<p>Thanks,</p>
<p> </p>
<p>Doug Collins</p>
<p>As you indicated, I don't know how well this would actually work, but I think it's a brilliant idea! I'm sorry that I have fixed the buzz now. I want to try it.</p>
<p> </p>
<p>I think it is a two person job though unless I can figure out how to attach the probe to the fret.</p>
<p> </p>
<p>Thanks,</p>
<p> </p>
<p>Doug Collins</p> Glad you got it figured out.…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:564822011-05-04T18:46:52.745ZMark Wallacehttps://fretsnet.ning.com/profile/MarkWallaceMarksFretShop
Glad you got it figured out. I have read about guys chasing down problem frets by using a multimeter (set to conductivity) or low wattage light looped through the bridge with the other end placed against the suspected fret(s). In principle the circuit would be completed when the string contacts the fret. I'm not sure how practical this would be given the frequency and limited duration in which this actual contact may occur.
Glad you got it figured out. I have read about guys chasing down problem frets by using a multimeter (set to conductivity) or low wattage light looped through the bridge with the other end placed against the suspected fret(s). In principle the circuit would be completed when the string contacts the fret. I'm not sure how practical this would be given the frequency and limited duration in which this actual contact may occur. Thanks for all the replies. …tag:fretsnet.ning.com,2011-05-04:2177249:Comment:563162011-05-04T17:59:14.353ZDoug Collinshttps://fretsnet.ning.com/profile/DougCollins
<p>Thanks for all the replies. I have the rocker tool (If I didn't, I really like that razor blade idea.) and I could not find any high frets.</p>
<p>To answer Mark's question, I do have relief - too much actually, but the buzz is still there.</p>
<p>I have now learned that the rocker tool, placed over three frets to find a high fret, is limited and in this particular case, deceiving. The problem is not a high fret, but rather a low fret.</p>
<p> </p>
<p>You might think that the rocker tool…</p>
<p>Thanks for all the replies. I have the rocker tool (If I didn't, I really like that razor blade idea.) and I could not find any high frets.</p>
<p>To answer Mark's question, I do have relief - too much actually, but the buzz is still there.</p>
<p>I have now learned that the rocker tool, placed over three frets to find a high fret, is limited and in this particular case, deceiving. The problem is not a high fret, but rather a low fret.</p>
<p> </p>
<p>You might think that the rocker tool would reveal that too, and in most cases it would, but this guitar had a dip in the neck and fingerboard. (kind of a built in bit of relief, only pronounced in one area) The low fret was level in relation to the next two frets, but maybe by the third fret away - not so much. If the rocker tool did find the next fret high (which it did first time around), filing down the fret did not solve the problem, it only moved it further up the neck.</p>
<p> </p>
<p>In the end, I had to remove all the frets and level the fingerboard itself.</p>
<p> </p>
<p>I don't know if I described this well enough or not, but it looks like I have solved my problem. Still, even just for curiosity, I wish there was a tool for listening or seeing a buzzing fret. (Maybe a mechanic stethoscope?) Does the buzz occur when fretting directly next to the high fret, or is it further away? One thing I do know is that filing down the fret that is causing the buzz may not be the proper thing to do, so maybe this tool would not be useful.</p>
<p> </p>
<p>Thanks for all the help,</p>
<p> </p>
<p>Doug Collins</p> When hearing the buzz, is the…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:561552011-05-04T16:30:56.991ZMark Wallacehttps://fretsnet.ning.com/profile/MarkWallaceMarksFretShop
<p>When hearing the buzz, is the neck dead straight or does it have some relief? </p>
<p>When hearing the buzz, is the neck dead straight or does it have some relief? </p> Yep, me too. The fret rocker…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:563062011-05-04T12:37:00.402ZMark McLeanhttps://fretsnet.ning.com/profile/MarkMcLean
<p>Yep, me too. The fret rocker is great for identifying a high fret that you can't pick by other methods. But any short straight edge would do the same job so that idea of using razor blade sounds neat!</p>
<p>Mark</p>
<p>Yep, me too. The fret rocker is great for identifying a high fret that you can't pick by other methods. But any short straight edge would do the same job so that idea of using razor blade sounds neat!</p>
<p>Mark</p> I stopped using that stewmac…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:562242011-05-04T12:08:48.204ZSTGuitarworkshttps://fretsnet.ning.com/profile/STGuitarworks
<p>I stopped using that stewmac fret rocker after working at a guitar manufacturer that used (blunted) snap off razors<a target="_self" href="http://storage.ning.com/topology/rest/1.0/file/get/2167736588?profile=original"><img width="220" src="http://storage.ning.com/topology/rest/1.0/file/get/2167736588?profile=original" class="align-left"/></a> for the same job.... cheaper, easier to purchase, not as critical to keep track of...</p>
<p>I stopped using that stewmac fret rocker after working at a guitar manufacturer that used (blunted) snap off razors<a target="_self" href="http://storage.ning.com/topology/rest/1.0/file/get/2167736588?profile=original"><img width="220" src="http://storage.ning.com/topology/rest/1.0/file/get/2167736588?profile=original" class="align-left"/></a> for the same job.... cheaper, easier to purchase, not as critical to keep track of...</p> I agree 101% with Grahame! I…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:560602011-05-04T11:55:07.558ZChris Rochowhttps://fretsnet.ning.com/profile/ChrisRochow
I agree 101% with Grahame! I use it ALL the time!! In a 'pinch', if you don't have this tool. You can use a old credit card to place over 3 frets at a time...... using the short edge of the card once you get around teh 8-9th fret.
I agree 101% with Grahame! I use it ALL the time!! In a 'pinch', if you don't have this tool. You can use a old credit card to place over 3 frets at a time...... using the short edge of the card once you get around teh 8-9th fret. I once had this problem. The…tag:fretsnet.ning.com,2011-05-04:2177249:Comment:560572011-05-04T09:55:09.882ZBob Steinarssonhttps://fretsnet.ning.com/profile/BobSteinarsson
<p>I once had this problem. The string appeared to be bent, even when under tension. The strings on that guitar were very heavy gauge, I think .016 to .60.-something, tuned in G. New strings solved the problem.</p>
<p>Good luck!</p>
<p>Bob</p>
<p> </p>
<p>I once had this problem. The string appeared to be bent, even when under tension. The strings on that guitar were very heavy gauge, I think .016 to .60.-something, tuned in G. New strings solved the problem.</p>
<p>Good luck!</p>
<p>Bob</p>
<p> </p>